Overview
The Rogue Infinity Crossmembers are a versatile series of structural components and pull-up bars designed specifically for the Rogue Infinity and Monster Lite series. These crossmembers allow gym owners to expand their rigs and racks, add new workstations, and significantly increase the overall stability of their units. Manufactured from 7-gauge steel in the USA, they offer a wide range of lengths and diameters to suit any training environment, from garage gyms to large-scale CrossFit affiliates.
Key Features and Specifications
Construction: Heavy-duty 7-gauge steel for long-term durability and safety.
Compatibility: Exclusively designed for the Rogue Infinity Series and Monster Lite Series (uprights with 5/8” holes).
Length Options: Available in standard 43” (for power racks) and 70” (for rig sections) spans.
Diameter Variants:
Skinny: 1.25” Outside Diameter (OD).
Fat: 2.0” Outside Diameter (OD).
Profile Selection:
Single Pull-up Bars (Skinny or Fat).
Double Bars (Fat/Skinny combination).
Rectangular Beam Crossmembers (X-43 and X-70).
Weight Capacity: Tested and rated for 500LB+.
Finish: Signature Texture Black powder coat for a secure, chalk-receptive grip.
Manufacturing: Proudly Made in the USA.
Note: Hardware is NOT included with these crossmembers and must be purchased separately.
Performance Benefits
Enhanced Structural Rigidity: Adding rectangular beam crossmembers (X-43/X-70) to the top or rear of a rack significantly reduces lateral sway, creating a more stable environment for heavy lifting and dynamic movements.
Functional Expansion: The variety of 70" options allows for "daisy-chaining" rigs together, creating continuous pull-up stations and muscle-up zones across large floor plans.
Grip Diversity: By incorporating "Fat" (2") bars, athletes can focus on developing superior grip and forearm strength, while "Skinny" (1.25") bars remain the standard for gymnastics and high-volume pull-up work.
Modular Versatility: These crossmembers serve as excellent anchor points for hanging accessories like gymnastic rings, climbing ropes, and resistance bands.
Maintenance and Care
Coating Maintenance: Regularly wipe down pull-up bars with a damp cloth to remove sweat and oils. Use a nylon bristle brush to clear out packed-in chalk from the textured powder coat.
Hardware Inspection: Since hardware is not included, ensure you are using high-quality 5/8" bolts and check them periodically for tightness. Dynamic gymnastics movements can cause hardware to settle or loosen over time.
Rust Prevention: For units in high-humidity or non-climate-controlled spaces, wipe the steel dry after use. If the powder coat is chipped, apply a rust-inhibiting touch-up paint to the exposed steel.
Corner Protection: During assembly, ensure the mounting flanges are aligned properly to prevent bending or marring the upright finish.
Warranty Information
Rogue Fitness provides a Limited Lifetime Warranty on the structural welds and frames of the Rogue Infinity Crossmembers for the original purchaser. This warranty ensures the products are free from defects in material and workmanship. The powder coat finish is not covered under the lifetime warranty, nor is damage resulting from improper installation or the use of incorrect mounting hardware.
Frequently Asked Questions
Q: Why is hardware not included? A: Rogue sells these components individually to allow for maximum customization. Because hardware requirements (bolt length and finish) vary depending on your specific rack configuration, Rogue leaves the hardware selection to the user to ensure the correct fit.
Q: Can I use these on a 3x3" Monster Lite rack? A: Yes. While designed for the Infinity series, the 5/8" hole pattern is identical to the Monster Lite series, making these crossmembers fully cross-compatible.
Q: What is the benefit of a 70" crossmember over a 43"? A: The 70" crossmember is designed for rig sections, providing enough width for two athletes to work simultaneously or for creating specialized muscle-up stations with extra clearance.
Q: Do these fit on a Monster Series rack? A: No. Monster Series racks use 1" hardware. These crossmembers are specifically for 5/8" hardware systems.