Overview
The Rogue 70" Single Pull-Up Bar 2.0 is a fundamental structural component designed for Rogue Infinity and Monster Lite rigs and wall-mount systems. Measuring 70 inches in length, this bar is primarily used to create wide pull-up stations or to bridge the gap between two rig sections. The 2.0 version features an improved pass-through gusset design, allowing for greater vertical adjustability on the uprights and a more streamlined installation compared to original models.
Key Features and Specifications
Construction: Heavy-duty steel with a 1.25” Outside Diameter (OD).
Compatibility: Exclusively designed for Infinity (2x3") and Monster Lite (3x3") Series (units with 5/8” holes).
Length: 70” (Standard span for rig "lanes").
Gusset Design: Upgraded pass-through gussets (Version 2.0) that allow the bar to be mounted at any height along the upright without being obstructed by the gusset plate.
Weight Capacity: Rated for 500LB+ when properly installed on a secured rig.
Finish: Signature Texture Black powder coat for a superior, chalk-friendly grip.
Manufacturing: Proudly Made in the USA.
Note: Hardware is NOT included and must be purchased separately.
Performance Benefits
Multi-Athlete Workstation: The 70" span is wide enough to accommodate two athletes performing synchronized movements or to provide a single athlete with ample space for high-momentum kipping and butterfly pull-ups.
Rig Stabilization: Acting as a massive lateral bridge, the Rogue 70" Single Pull-Up Bar 2.0 significantly reduces rack "sway" and increases the overall structural integrity of large rig configurations.
Optimized for Muscle-Ups: The extra width provides the necessary clearance for athletes to perform ring or bar muscle-ups without the risk of making contact with the rig uprights.
Versatile Accessory Anchor: This bar serves as a robust mounting point for hanging heavy bags, climbing ropes, gymnastic rings, and resistance bands.
Maintenance and Care
Coating Preservation: Wipe the bar down after high-intensity sessions to remove sweat and oils. Use a nylon bristle brush to clear out dried chalk from the textured powder coat to maintain grip effectiveness.
Hardware Inspection: Periodically check the 5/8" mounting bolts. Because 70" bars often endure high-torque movements (like kipping), ensuring the hardware remains tight is critical for safety.
Rust Prevention: For rigs located in garage gyms or high-humidity environments, ensure the bar is kept dry. If the powder coat is chipped, apply a rust-inhibiting touch-up paint to the exposed steel.
Alignment Check: Ensure the gussets are seated flush against the uprights during installation to prevent uneven stress on the mounting bolts.
Warranty Information
Rogue Fitness provides a Limited Lifetime Warranty on the structural welds and frame of the Rogue 70" Single Pull-Up Bar 2.0 for the original purchaser. This warranty ensures the product is free from defects in material and workmanship. The warranty does not cover the powder coat finish, normal wear and tear, or damage resulting from improper installation or the use of non-Rogue hardware.
Frequently Asked Questions
Q: Can I mount this on a 43" wide power rack? A: No. This bar is 70" long and is intended for rig sections or wide wall-mount spans. For a standard power rack, you will need a 43" crossmember or pull-up bar.
Q: Why doesn't it come with bolts? A: Rogue sells these components individually to allow for maximum customization. Since the bolt length and finish (Bright Zinc vs. Black) depend on your specific upright size and aesthetic preference, hardware is sold as a separate kit.
Q: Does this fit on the Monster Series (1" hardware)? A: No. This bar is specifically for the Infinity and Monster Lite lines. The Monster Series requires 1" hardware and different gusset dimensions.
Q: Is this the same bar used in the SPEAL bar? A: No. The SPEAL bar is made of bare steel, whereas the standard 70" Single Pull-Up Bar 2.0 features a Texture Black powder coat. They share the same 2.0 gusset design but differ in surface finish.